Flange-Off Tool
Toilet Replacement Made Easy
Are you going to find a broken flange the next time you pull a toilet? Don’t let it slow you down! Remove that old flange in 5 minutes with the Flange-Off Tool invented by Woods Plumbing & Sewer Service. The days are gone of trying to cut and chip the old flange off, risking cracking the pipe, or choking down the drain by installing an insert flange. The Flange-off will cut the old flange off a 3” pipe without any risk of cracking the pipe, leaving the pipe ready to glue a new flange on the outside of the pipe! Patent pending.
Toilet Replacement Made Easy
Are you going to find a broken flange the next time you pull a toilet? Don’t let it slow you down! Remove that old flange in 5 minutes with the Flange-Off Tool invented by Woods Plumbing & Sewer Service. The days are gone of trying to cut and chip the old flange off, risking cracking the pipe, or choking down the drain by installing an insert flange. The Flange-off will cut the old flange off a 3” pipe without any risk of cracking the pipe, leaving the pipe ready to glue a new flange on the outside of the pipe! Patent pending.
Instructions
For professional use only . Do not attempt to use this tool unless you are Experienced at using large hole saw bits
Before inserting wedge into pipe, the top nut on the hollow shank of wedge may need to be adjusted so that the wedge slips snugly into pipe. To adjust tightness of wedge, grasp bottom of hollow shank and turn the top nut until the wedge fits into the pipe snugly.
Insert wedge into pipe. Tighten top nut until wedge cannot be pulled out by hand.
Attach hole saw to a drill. A strong electric angle drill will work best.
Insert arbor into hollow shank.
WITHOUT TOUCHING SAW TEETH TO PLASTIC FLANGE, start the drill spinning and SLOWLY lower teeth into flange to begin cutting.
IMPORTANT: UPON INITIAL CONTACT WITH THE TEETH OF THE SAW AND THE FLANGE, INSURE THAT THE DRILL IS HELD VERY SECURE WITH TWO HANDS AND IS ALIGNED PROPERLY INTO THE HOLLOW SHANK.
Continue to cut down through flange using very light pressure and keep drill aligned. For best results while drilling, raise the bit up out of the cut while spinning EVERY 2 SECONDS and then push it back down. This will spin out any built up PVC shavings and make cutting much easier. If drill bogs down….you have too many shavings under it.
Always wear safety goggles during use. Manufacturer is not responsible for misuse or abuse of product. Liability limited to purchase price of product. U.S. Patent Pending
Purchase the
Flange-Off Tool
You can purchase your own Flange-Off Tool at KECO Supply by calling
(405) 745-2145.
Instructions
For professional use only . Do not attempt to use this tool unless you are Experienced at using large hole saw bits
Before inserting wedge into pipe, the top nut on the hollow shank of wedge may need to be adjusted so that the wedge slips snugly into pipe. To adjust tightness of wedge, grasp bottom of hollow shank and turn the top nut until the wedge fits into the pipe snugly.
Insert wedge into pipe. Tighten top nut until wedge cannot be pulled out by hand.
Attach hole saw to a drill. A strong electric angle drill will work best.
Insert arbor into hollow shank.
WITHOUT TOUCHING SAW TEETH TO PLASTIC FLANGE, start the drill spinning and SLOWLY lower teeth into flange to begin cutting.
IMPORTANT: UPON INITIAL CONTACT WITH THE TEETH OF THE SAW AND THE FLANGE, INSURE THAT THE DRILL IS HELD VERY SECURE WITH TWO HANDS AND IS ALIGNED PROPERLY INTO THE HOLLOW SHANK.
Continue to cut down through flange using very light pressure and keep drill aligned. For best results while drilling, raise the bit up out of the cut while spinning EVERY 2 SECONDS and then push it back down. This will spin out any built up PVC shavings and make cutting much easier. If drill bogs down….you have too many shavings under it.
Always wear safety goggles during use. Manufacturer is not responsible for misuse or abuse of product. Liability limited to purchase price of product. U.S. Patent Pending
Purchase the
Flange-Off Tool
You can purchase your own Flange-Off Tool at KECO Supply by calling
(405) 745-2145.
Licensed in All OKC Metro Cities
Contact Information
Phone:
405-942-2803
Address: 1029 East Campbell Street Edmond, OK 73034
Visit Our Location
Licensed in All OKC Metro Cities
BROWSE OUR WEBSITE
CONTACT INFORMATION
Phone:
405-942-2803
Email: denniseck@reagan.com
Address: 1029 East Campbell Street Edmond, OK 73034
VISIT OUR LOCATION
Content, including images, displayed on this website is protected by copyright laws. Downloading, republication, retransmission or reproduction of content on this website is strictly prohibited. Terms of Use
| Privacy Policy